@elizabeth19638: #oldme

Catherine Huxtable
Catherine Huxtable
Open In TikTok:
Region: GB
Sunday 16 August 2020 20:09:48 GMT
81
6
1
0

Music

Download

Comments

gazguy0
user2387646026604 :
🥰😂😂😂
2020-08-16 20:47:33
0
To see more videos from user @elizabeth19638, please go to the Tikwm homepage.

Other Videos

Step by step instructions ⬇️ Supplies Needed:  Spray paint, shovel, rake, work gloves, hand tamper/plate compactor, weed barrier, paver sand, your chosen pavers (we used 24”x16”), level, plastic edging & stakes, hammer, utility knife, wheelbarrow, tape measure, white marble rock, Dominator Mulch Glue, garden sprayer, and Dominator Wet Look Paver Sealer. Here’s how ya do it: ➡️Clear and roughly level your area, ensuring a slight slope for drainage. Compact the soil thoroughly. Mark your walkway's perimeter with spray paint (ours is 48” wide!), then install plastic paver edging firmly along your lines. ➡️Lay down landscape weed barrier and secure it with stakes. Spread 1-2 inches of paver sand, smoothing it out (don't compact yet!). Start laying your pavers, maintaining consistent spacing (we used an 11-inch gap between our 24”x16” pavers, using a 24”x11” styrofoam guide). Gently tap each paver level with a rubber mallet, adding sand underneath if needed. For extra stability, we nailed two plastic edging stakes on each side of every paver. ➡️Spread your rock evenly around the pavers, (ours vary in size from 1/2”- 2”) making sure it's level with the paver tops. Rinse and wash all dust and dirt from the rocks and pavers – let them dry completely! Then, spray Dominator Mulch Glue generously over the marble rock (undiluted, up to 3 coats or larger rock) letting it dry between applications. Finish by applying two thin coats of Dominator Wet Look Paver Sealer to your pavers, backrolling any excess. Allow ample curing time. ➡️ Let us know what questions you have! @BDCBrands #DIY #diyproject #asmr #Outdoors #tutorial #howto
Step by step instructions ⬇️ Supplies Needed: Spray paint, shovel, rake, work gloves, hand tamper/plate compactor, weed barrier, paver sand, your chosen pavers (we used 24”x16”), level, plastic edging & stakes, hammer, utility knife, wheelbarrow, tape measure, white marble rock, Dominator Mulch Glue, garden sprayer, and Dominator Wet Look Paver Sealer. Here’s how ya do it: ➡️Clear and roughly level your area, ensuring a slight slope for drainage. Compact the soil thoroughly. Mark your walkway's perimeter with spray paint (ours is 48” wide!), then install plastic paver edging firmly along your lines. ➡️Lay down landscape weed barrier and secure it with stakes. Spread 1-2 inches of paver sand, smoothing it out (don't compact yet!). Start laying your pavers, maintaining consistent spacing (we used an 11-inch gap between our 24”x16” pavers, using a 24”x11” styrofoam guide). Gently tap each paver level with a rubber mallet, adding sand underneath if needed. For extra stability, we nailed two plastic edging stakes on each side of every paver. ➡️Spread your rock evenly around the pavers, (ours vary in size from 1/2”- 2”) making sure it's level with the paver tops. Rinse and wash all dust and dirt from the rocks and pavers – let them dry completely! Then, spray Dominator Mulch Glue generously over the marble rock (undiluted, up to 3 coats or larger rock) letting it dry between applications. Finish by applying two thin coats of Dominator Wet Look Paver Sealer to your pavers, backrolling any excess. Allow ample curing time. ➡️ Let us know what questions you have! @BDCBrands #DIY #diyproject #asmr #Outdoors #tutorial #howto

About