Jason Garner
Region: US
Monday 06 September 2021 23:11:11 GMT
1180789
10194
443
25
Music
Download
Comments
fishing_c_1997 :
Bruh just measure twice and cut once 😂
2021-09-06 23:52:30
61
user3830340787100 :
use your catpaw! if you know you know.
2021-09-06 23:55:04
154
pinshooter :
Hit it with your purse!!
2021-09-07 13:00:22
97
Maihan :
Chisel and hammer trick
2021-09-07 11:51:36
38
@jeffreyknoxville :
Jam a pointed 2x4 in the ground then push or pull the beam
2021-09-06 23:17:14
20
Shawn Dissents :
spud bar in the ground
2021-10-02 23:47:14
8
Willblob64 :
instead of moving the board. move the mark haha😂
2021-09-08 03:07:00
6
jjkillz :
Get a bigger hammer😂😂😂😂😂😂😂😂😂
2021-09-07 23:30:42
4
Jeremy Edward :
clamp works... swap the stationary end to the other end of the bar, it will spread. attach a block to the board. squeeze clamp👍
2021-09-12 12:38:32
3
Balloon Animal :
Can’t you just use a pipe clamp and turn one end sideways
2021-10-03 17:23:46
2
Cs :
Scrap block of 2x4 and a hammer. Tap it until it’s in place.
2021-09-09 19:41:22
2
Darth_Vader_Lives(no live) :
LOL, it is called a saw.
2021-09-25 20:35:03
1
Dylan Patrick Waldro :
screw a 2x4 in front of that board and use your hammer to pry between them.
2021-09-12 00:29:12
1
mshark :
I usually just start talking to them about my life it pushes them away pretty fast
2021-09-16 14:31:55
0
Joey Curtis :
use a screw...as a fulcrum instead of a pinned end.
2022-01-01 04:42:12
0
Geauxyo :
flatbar
2021-09-07 01:46:38
0
Dilbertisreal :
Drive a large flat screwdriver back under the board a little as needed and pry
2021-09-07 01:46:47
0
333rem :
Hammer it
2021-09-07 01:58:40
0
johnny :
put a nail in the side of the 2x6 to act as a fulcrum. use a piece of scrap lumber as a lever to push the fulcrum away from the post. if...
2021-09-07 02:03:38
0
c :
use leaver/claw bar and screw
2021-09-07 02:03:49
0
Tray Coker :
Screw in a pry board with a small gap between it and the far end of the base board.
2021-09-07 02:28:18
0
JC Benavides :
cut the board the right size. .....ok I'm kidding.
2021-09-07 02:53:44
0
Tanner James :
Catclaw or chisel in and lever
2021-09-17 21:37:46
0
Ray Bubba Martinez :
Bar clamp
2021-09-07 03:58:49
0
user3442985420457 :
tie one end of a rope to a Ford ranger, and you can figure it out from there
2021-09-07 04:06:38
0
user5560811524903 :
Keep clamping
2021-09-07 04:14:53
0
Carl Carlson :
use a 3/4x24" long bar clamp not a quick clamp. you'll get Way more force with that.
2021-09-07 04:15:18
0
wilkinson7b :
pound chisel, pry.
2021-09-07 04:59:01
0
meltre80 🇨🇦🇨🇦 :
wood chisel works
2021-09-07 05:33:35
0
user3647777516949 :
use a sliding Bessy clamp you can move the world with one of those
2021-09-07 05:46:09
0
raines wilson :
2 nails at about the width of your hammer nail puller arm things, get it as close as you can to the board you wanna push with still fitting the hammer
2021-09-07 05:57:36
0
Travis :
A block and a wedge
2021-09-18 00:13:21
0
Christian C :
Hammer pry bar into edge and pry
2021-09-07 07:28:34
0
Nate Villegas846 :
10 lb hammer.
2021-09-07 08:13:31
0
variablepoem :
bang a chisel in and push
2021-09-07 09:07:29
0
Jj Grant :
Put a block on the face of the top bit of timber so it over hangs the bottom bit, put a screw in the face of bottom bit of timber and crank on it pt1
2021-09-07 09:35:27
0
GO TRUMP2 :
Crowbar,
2021-09-07 10:27:07
0
Tom Megale :
cut more off lol
2021-09-07 10:31:24
0
jbowmancarpentry :
You could use the same screw and hammer trick. Put the screw in the treated beam, add a 2 1/2 block at the end of the 2x6.
2021-09-07 11:25:19
0
Sean Staidl :
use the screw and hammer for both. works great both ways
2021-09-07 11:49:51
0
thomas :
fip the head the other way
2021-09-07 14:08:34
0
Andy Calhoun :
Anchor the other side, leverage in the middle.
2021-09-07 14:40:21
0
Ryan :
good one😏
2021-09-07 14:42:16
0
Jim Goenen :
if you don't know stop F'n around a hire a pro.
2021-09-07 14:47:57
0
law of the land :
a drift with a sharp point hammer it in pry and screw
2021-09-07 14:50:26
0
To see more videos from user @postworksllc, please go to the Tikwm
homepage.
