Darius Stcyr
Region: US
Sunday 11 May 2025 13:22:01 GMT
13849
197
55
4
Music
Download
Comments
Jamie Gack :
that impeller is shot, it's got memory and they lose effectiveness that way. also, those plastic housings will warp, yamaha i always do the housings. replace the keyway too, use a small punch to
2025-05-11 13:38:06
9
maybepepe_ :
Ooff id change the whole lower unit if possible, I heard you got parts coming in DM if anything boss 🔥
2025-05-11 16:41:27
1
user174040871404 :
You can find the kit on Amazon
2025-05-13 17:00:47
1
Tony Caristi :
That’s also the wrong water pump housing
2025-05-12 18:55:43
1
cj5150 crazy john :
The impeller should not turn without turning the shaft there is a key that fits in the impeller and the flat spot on the shaft
2025-05-11 22:27:04
2
Bigowl :
Looking outstanding for a good boat
2025-06-08 21:42:24
1
jamesfuller925 :
You have a sheared woodruff key or not a key at all
2025-05-16 02:24:19
1
michaelh11 :
If it's a saltwater engine, you probably have a lot of buildup behind the water jacket. I've also had no water conditions due to debris stuck in the thermostat housing.... On a side note, replace that impeller.
2025-05-14 20:56:46
1
Dakotah Socks :
There should be a key for driveshaft and the water pump when you spin drive shaft the water pump should turn too
2025-05-11 20:02:43
2
JohnnyFishing 🎣 :
easy fix
2025-05-14 02:39:58
1
Joseph_thatranger :
The thing u broke just goes to ur speedometer so if u care abt it then replace it but if u don’t care then u can run without
2025-05-12 03:52:30
2
𝓙𝓮𝓼𝓼𝓮 𝓑𝓻𝓸𝔀𝓷 :
Take your thermostat out and see if the blockage is in there
2025-05-11 23:32:22
1
user6551896056115 :
Bro you got it
2025-05-12 00:55:52
1
GinaBean2587 :
the way everyone showed up in the comments on your boat venture is pure love!!!! 🥰
2025-05-11 14:52:43
1
bill :
that's why you need to run engine in a barrow
2025-05-11 21:00:18
2
kenny :
That impeller is shot. Find shouldn’t be bent like that. Look at a new one
2025-05-12 14:00:44
1
Capt.Jay :
stick a little rod small enough to go threw tube..coat hanger might work..your tube up on motor might be clogged..happens all the time on my twins
2025-05-12 11:17:05
2
Dirt digger :
Needs a new water pump and housing and the black stuff with the oil that’s where you’re exhausting is nothing to worry about
2025-05-12 01:31:21
1
Jody Hale :
Get a piece of wire and make sure the hole is cleaned out. Dirt dobbers love to get in those water pump outlet lines
2025-05-12 13:18:07
1
Mike Berry :
check your thermostat it's on the top the motor
2025-05-11 19:33:33
1
Chewy33 :
You don’t need the pice in the front it will run with out it just pedac tube
2025-05-13 23:00:47
1
Roger Pettis187 :
Replace the impeller, housing, gaskets, seal plate. All of it
2025-05-12 03:46:52
1
Tony Caristi :
Driveshaft seals under the water pump
2025-05-12 18:55:11
1
Michael Banks343 :
Change impeller bad
2025-05-11 14:25:13
1
Bear :
Keep the motor tilted up, remove the thermostat & fill it up with CLR overnight.
2025-05-11 15:15:59
1
To see more videos from user @dariusstcyr, please go to the Tikwm
homepage.
