Tailored Tree Care
Region: AU
Friday 01 August 2025 04:48:33 GMT
33293
495
110
6
Music
Download
Comments
Fletcher :
Air leak obviously. Either around the carby and manifold, or cylinder bolts are loose and a broken cylinder gasket. Mostly cylinder. At level, gravity is holding down the cylinder down but when you point the bar down the cylinder slightly tilts forwards opening the air leak
2025-08-01 08:49:12
67
Saxon King :
The bar being upside down on YOUR saw hurts MY head.
2025-08-03 05:27:43
0
Wentzell19 :
Air leak on the carb boot more then likely, when the saw is tipped down it flexes the boot. Common issue when just jam a saw and just yank and rip on it to get it out
2025-08-02 15:30:14
2
Jay :
Crank seals, drawing air into the cylinder. Mix up some soapy water and spray around the crank seals and it will start bubbling 👍🏼
2025-08-01 18:40:00
1
bb_5004 :
Either your anti vibrant stuff is a Bit loose and your saw gets on the Trigger or something or your Membran in the carburator is a Bit old and you should get a new one i have the Same Problem on my Stihl 08s but i dont change anything because i dont work with it anymore
2025-08-02 22:03:49
0
Tjillivippen :
Its the vibration bushings!
2025-08-02 22:22:17
0
Bailey_lindner :
Reason for that is it’s a stihl mate. Try going hasqvarna that’ll fix it😏
2025-08-01 08:11:19
11
kristjan🇦🇱 :
could it be idle rpms too high amd needs to be lowered?
2025-08-01 22:20:14
0
hydnnnt :
Clutch spring?
2025-08-01 05:30:52
0
im.diablo.the.3rd :
my 039 did this, i re tuned it and it stopped
2025-08-01 06:03:26
0
Stephen4033 :
The problem is its a sthil not a husky.
2025-08-02 00:43:16
0
vandoswoodshop :
bar is upside-down
2025-08-01 08:31:22
19
Bubbles :
Does that have the m tronic playing up
2025-08-01 05:18:17
0
Sir_Daragon :
Gravity pulls on the chain and the chain runs the engine
2025-08-02 20:38:01
0
Jay kinnear :
Ain’t got no gas innit
2025-08-01 09:34:59
0
🅖🅔🅞🅡🅖🅔 :
do a leak test asap. I'm 100% positive that one of the bearing seals is done, and I tend to believe it's the clutch side who's damaged. for sure it ran lean and got hot❗
2025-08-02 15:51:27
0
RumHam :
its got hill start assist
2025-08-01 07:43:19
8
bigharriscampbell :
The float in the carb ain’t right
2025-08-01 17:57:46
5
user8771736210069 :
The chain bar needs to be flipped 👍
2025-08-01 09:33:31
2
Shubs :
Definitely the alternator
2025-08-01 22:15:34
0
ronniecahalane :
It's a stihl saw so your meant to keep it still
2025-08-01 20:28:22
2
Nathan Price815 :
Ent got no gas in it
2025-08-02 21:54:49
0
Physics Over Voodoo :
Have a look at your anti vibe mounts. If they are stuffed it'll pull on the throttle linkage as you tilt forward
2025-08-01 09:26:13
2
ausoneten :
Cause the bar is on upside down
2025-08-01 09:48:20
0
Gumboot :
usually its the rubber bit that gos from the Air intake to the head..
2025-08-02 02:42:57
0
To see more videos from user @tailoredtreecare, please go to the Tikwm
homepage.
